Self employment provides an individual with the freedom to control their time and to determine how much money they earn. Many people have discovered this and ventured in many businesses, among them agriculture. In this sector, poultry farming has become very common. There arose the need lessen the work load for those who keep meet chicken and especially when removing the feathers. The result was the development of how to make a chicken plucker procedure.
To achieve good results while making it, assemble all the tools and equipment that are needed. Some may be locally available while others may have to be bought from the concerned retailers. Some of them include but not limited to; screws, pieces of rubber, coupling and so on. However, should the process of putting them together prove to be too difficult, then a professional who knows how to do it may be consulted.
The procedure could be dangerous and dirty. However, with the use of good shields, all will turn out well. Cloves, aprons, overalls and welding spectacles are some of those that should be used to provide maximum protection. When the machine is in use, they should be worn too to ascertain that the clothes underneath do not get dirty.
Get another smooth board cut to required size, and have four perforations on which the engine will be secured on. This piece of wood and the first are put together and the motor placed on its place. The smoothness of the wood must be a priority.
On the next wood, put together with a third piece. This, just like the other two, has to be cut to size. It should be smooth too. Smooth out the corners at forty five degrees. Be very precise about this. The electric transmitter is then attached beside the engine. The motor, cord and the switch are then cabled together.
Then the preparations to attach the plucking fingers are due to begin. Make holes all round the plastic cap. They should be close together to achieve good results. However, the size of the lid will determine the distance between the holes. The smaller the lid the more the holes will be close together.The opposite is the case. They should be made all round the top. Then the rubber fingers are ready to be inserted form the inside to the outside.
At the middle bottom of the cover, make an opening. It should fit the rod tightly so do not have it too wide. This will provide support for the lid as it goes round. On the side of the engine is where the rod is attached firmly, preferably with the use of electricity. Use nuts to attach the cap and the rod together.
The task could be very tedious. It could also pose a great challenge at first when making it. However, watching and learning from others would be the best way to know how to make a chicken plucker. There are those that are already made and ready for purchase.
To achieve good results while making it, assemble all the tools and equipment that are needed. Some may be locally available while others may have to be bought from the concerned retailers. Some of them include but not limited to; screws, pieces of rubber, coupling and so on. However, should the process of putting them together prove to be too difficult, then a professional who knows how to do it may be consulted.
The procedure could be dangerous and dirty. However, with the use of good shields, all will turn out well. Cloves, aprons, overalls and welding spectacles are some of those that should be used to provide maximum protection. When the machine is in use, they should be worn too to ascertain that the clothes underneath do not get dirty.
Get another smooth board cut to required size, and have four perforations on which the engine will be secured on. This piece of wood and the first are put together and the motor placed on its place. The smoothness of the wood must be a priority.
On the next wood, put together with a third piece. This, just like the other two, has to be cut to size. It should be smooth too. Smooth out the corners at forty five degrees. Be very precise about this. The electric transmitter is then attached beside the engine. The motor, cord and the switch are then cabled together.
Then the preparations to attach the plucking fingers are due to begin. Make holes all round the plastic cap. They should be close together to achieve good results. However, the size of the lid will determine the distance between the holes. The smaller the lid the more the holes will be close together.The opposite is the case. They should be made all round the top. Then the rubber fingers are ready to be inserted form the inside to the outside.
At the middle bottom of the cover, make an opening. It should fit the rod tightly so do not have it too wide. This will provide support for the lid as it goes round. On the side of the engine is where the rod is attached firmly, preferably with the use of electricity. Use nuts to attach the cap and the rod together.
The task could be very tedious. It could also pose a great challenge at first when making it. However, watching and learning from others would be the best way to know how to make a chicken plucker. There are those that are already made and ready for purchase.
Aucun commentaire:
Enregistrer un commentaire